镍基高温合金GH202高温氧化后的微观组织演变

研究了镍基高温合金GH202在800~1100 ℃高温氧化后晶粒、碳化物和强化相的演变过程。采用透射电子显微镜、扫描电子显微镜和电子背散射衍射对其微观结构进行了表征。结果表明：镍基高温合金的硬度随氧化温度的升高而降低，1100 ℃氧化100 h后，硬度降低了43.5%。800和900 ℃氧化后晶粒生长速度较慢，而经900 ℃氧化后晶界碳化物析出显著增加。在1000和1100 ℃氧化后，晶粒尺寸明显增大。氧化过程中晶界迁移是由晶界两侧自由能差决定，温度越高，晶界向曲率中心迁移越快，大量细小晶粒被吞并形成了大晶粒。大块状碳化物（MC）分解成大量的碳原子，与Cr原子结合形成少量的富Cr颗粒状M₂₃C₆。在900 ℃氧化150 h后，M₂₃C₆演化为富Ti的M₆C。随着氧化温度的升高，碳化物在γ相中回熔。在800、900和1000 ℃氧化后，γ′相逐渐长大，在1100 ℃氧化100 h后，完全溶解于γ相。     

珠江口盆地珠一坳陷古近系高自然伽马砂岩形成机制及油气地质意义

运用放射性元素寻找油气是一种非常规油气勘探手段。近年来,在珠江口盆地珠一坳陷富烃凹陷周边古近系钻遇高自然伽马(GR)砂岩,其GR值(100~300 API)甚至大于同区泥岩的GR值(100~200 API)。为了弄清该特殊现象背后的地质意义,对珠江口盆地珠一坳陷古近系高自然伽马砂岩开展了铀(U)、钍(Th)、钾(K)等3种元素含量与GR值的相关趋势线分析,从井震特征、岩性特征及矿物成分特征等入手分析了砂岩GR值增高的主要原因及成因机制,探讨了放射性元素聚集的条件、运移通道、驱动力以及油气意义。结果表明:西江、惠州地区由U含量增高导致砂岩GR值偏高,恩平、番禺地区由K,Th含量增高导致砂岩GR值偏高;砂岩GR值增高有两大成因机制,一是地下流体带来的放射性元素离子U4+在氧化-还原面处富集后导致地层GR值偏高,这种特殊现象说明在具有连通基底大断裂旁的圈闭中,U4+的富集指示了曾经油气的存在,证实了研究区油气运移通道的有效性,对于油气藏的预测有着非常重要的指导性意义,二是地表流体带来的含放射性元素的矿物大量沉积后导致地层GR值偏高,含放射性元素矿物性质不稳定,可指示近源供给的存在,对于判断物源及沉积环境有着非常重要的意义。该研究成果为预测研究区油气成藏有利区带提供了依据。     

磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Agronomic performance of high oleic,low linolenic soybean in Tennessee

Soybean oil hydrogenation alters the linolenic acid molecule to prevent the oil from becoming rancid, however, health reports have indicated trans-fat caused by hydrogenation, is not generally regarded as safe. Typical soybeans contain approximately 80 g kg⁻¹ to 120 g kg⁻¹ linolenic acid and 240 g kg⁻¹ of oleic acid. In an effort to accommodate the need for high-quality oil, the United Soybean Board introduced an industry standard for a high oleic acid greater than 750 g kg⁻¹ and linolenic acid less than 30 g kg⁻¹ oil. By combing mutations in the soybean plant at four loci, FAD2-1A and FAD2-1B, oleate desaturase genes and FAD3A and FAD3C, linoleate desaturase genes, and seed oil will not require hydrogenation to prevent oxidation and produce high-quality oil. In 2017 and 2018, a study comparing four near-isogenic lines across multiple Tennessee locations was performed to identify agronomic traits associated with mutations in FAD3A and FAD3C loci, while holding FAD2-1A and FAD2-1B constant in the mutant (high oleic) state. Soybean lines were assessed for yield and oil quality based on mutations at FAD2-1 and FAD3 loci. Variations of wild-type and mutant genotypes were compared at FAD3A and FAD3C loci. Analysis using a generalized linear mixed model in SAS 9.4, indicated no yield drag or other negative agronomic traits associated with the high oleic and low linolenic acid genotype. All four mutations of fad2-1A, fad2-1B, fad3A, and fad3C were determined as necessary to produce a soybean with the new industry standard (>750 g kg⁻¹ oleic and <30 g kg⁻¹ linolenic acid) in a maturity group-IV-Late cultivar for Tennessee growers.     

广西2021年早晚籼优质稻主要品种品质测报分析（网络首发、推荐阅读）

通过对广西2021年度推广种植的野香优、广粮香2号、百香、丝香四个主要品种系列的早晚籼优质稻谷品种进行采样，按照《优质稻谷》《中国好粮油 稻谷》《广西好粮油 广西香米》标准中规定质量品质指标进行检测，并依据检测数据对四个主要稻谷品种在不同季节、不同种植区域以及同一种植区域不同种植季节品质变化情况进行对比分析研究，寻找优质稻因品种、产地、种植季节不同对其品质的影响规律，为优质稻谷品种的选育和推广种植工作提供科学依据和数据支持，促进广西优质粮食产业和“广西香米”产业进一步发展。     

Implication of Size-Controlled Graphite Nanosheets as Building Blocks for Thermal Conductive Three-Dimensional Framework Architecture of Nanocarbons

Preparation of three-dimensional (3D) networks has received significant attention as an effective approach for applications involving transport phenomena, such as thermal management materials, and several nanomaterials have been examined as potential building blocks of 3D networks for the improvement of heat conduction in polymer nanocomposites. For that purpose, nanocarbons such as graphene and graphite nanoplatelets have been spotlighted as suitable filler materials because of their excellent thermal conductivities (ca. 10²–10³ W·(m·K)^?1 along their lateral axes) and morphological merits. However, the implications of morphological features such as the lateral length and thickness of graphene or graphene-like materials have not yet been identified. In this study, a controlled dissociation of bulk graphite to graphite nanosheets (GNSs) using a low-cost, ecofriendly bead mill process was extensively examined and, when configured in a 3D framework architecture formation, the size-controlled GNSs demonstrated that the thermal conductivities of a 3D interconnected framework of GNSs and the corresponding polymer nanocomposite were intimately correlated with the size of the GNSs, thus demonstrating the successful preparation of an efficient thermal management material without highly sophisticated efforts. The capability of controlling the lateral size and thickness of the GNSs as well as the use of a 3D interconnected framework architecture should greatly assist the commercialization of high-quality graphene-based thermal management materials in a scalable production process.     

Chia Seed Oil Prevents High Fat Diet Induced Hyperlipidemia and Oxidative Stress in Mice

Hyperlipidemia is a common cardiovascular disease. At present, the influence of high fat diet (HFD) on this is being explored. Recently, vegetable oils rich in omega‐3 have been reported that can treat hyperlipidemia caused by HFD. However, the effects of chia seed oil (CSO) on HFD‐induced hyperlipidemia and oxidative stress are poorly studied. Hence, in this study, the effects of CSO on hyperlipidemia and oxidative stress induced by HFD in mice are analyzed by various commercial kits, section staining, and protein expression. The results show that CSO decreases body weight and organ index. Meanwhile, CSO reduces serum lipid levels of total cholesterol, triglyceride, and low‐density lipoprotein cholesterol. It can also elevate superoxide dismutase and glutathione peroxidase activities and reduce malondialdehyde content in serum and liver. The results of histopathological analysis prove that CSO improves hepatic steatosis and reduces lipid deposition. Further, the results of western blot demonstrate that CSO upregulates the expression of peroxisome proliferator‐activated receptor alpha and carnitine palmitoyltransferase 1a in the liver. As a result, CSO may be a potential lipid‐lowering oil to prevent and treat HFD‐induced hyperlipidemia and oxidative stress. Practical Applications CSO, as a byproduct of chia seed processing, is a rich source of α‐linolenic acid. This study investigates the effects of CSO on HFD‐induced hyperlipidemia and oxidative stress in mice. It is concluded that dietary CSO can improve the hyperlipidemia in HFD‐induced mice via analysis of lipid parameters, histopathology study of the liver, and lipid metabolism related genes. In addition, supplementation of CSO also can improve the oxidative stress in mice. Therefore, CSO can be used for the prevention of hyperlipidemia and oxidative stress. This research provides a theoretical basis for the comprehensive development and utilization of functional chia seed oil.     

Tribological behavior studies of chemically bonded phosphate ceramic coatings reinforced with modified multi-walled carbon nanotubes (MWCNTs)

To improve the wear resistance of the chemically bonded phosphate ceramic coatings, MWCNTs are selected as the reinforcement after the modification. The high temperature wear experiment is carried out to investigate the wear behavior of the coatings with different temperatures. The results suggest that, when the temperature is below 500℃, MWCNTs can decrease friction coefficient, and the lowest friction coefficient is about 0.28, but MWCNTs lose the lubricant function at 500℃ and the friction coefficient keeps at the level of ~ 0.68. In addition, the wear resistance of coatings is improved with the introduction of MWCNTs at 100℃ and 300℃ (the wear rate is below 15X10^-3mm³/Nm), but keeps similar level at 500℃ (the wear rate is ~ 22 × 10⁻³mm³/Nm). Besides, the wear mechanism of the coatings reinforced by MWCNTs is also investigated based on the wear behavior and microstructural characterizations. MWCNTs improve the fracture toughness by preventing the crack generation and forming the bridge when crack occurs, which leads to smooth wear tracks and good wear resistance of coatings. The coatings with MWCNTs achieve poor wear resistance at 500℃ because MWCNTs lose their strength and resistance to fatigue by oxidizing.     

高地压严重突出区域下向穿层钻孔预抽消突技术

利用工作面高抽巷施工掩护顺槽掘进工作面下向穿层条带预抽钻孔,通过对钻场底板深、浅孔注浆封堵围岩裂隙解决了孔内返水不畅难题;采取了"两堵一注"封孔方式确保封孔严密不漏气;孔内全程下吹水管,实现了单孔、分组、定时吹水工作目标,提高了下向消突钻孔抽采效果,形成了一套高效、快速的下向穿层钻孔消突管理模式,实现了高地压严重突出区域煤层高效消突以及技术经济一体化目标,安全经济效益显著。